Crosswire for recanalization of total occlusive coronary arteries

Coronary angioplasty of total occlusions is technically difficult and is associated with limited success rates. The procedural outcome is mainly determined by the underlying pathological process. Recanalization of total occlusions is aimed at finding the passage with least resistance, without causing dissection or perforation. Several techniques have been advocated to improve the overall success rate. Recently, a new 0.014" Nitinol wire (Crosswire, Terumo) has been introduced as a tool, to achieve higher success rates for total occlusion angioplasty. The wire consists of an extremely flexible Nitinol-core, a platinum/iridium coil at the distal tip, and a hydrophilic polymer coating. Balloon angioplasty was attempted in 30 totally occluded coronary arteries with mean age of occlusion being 5 +/- 4 months (range 2-14 months). The initial five procedures were performed following failure of the conventional angioplasty guidewires. Subsequently, Cross-wire was used electively in all the cases. The lesion was crossed successfully in 90% (27/30) cases. Dissection of the coronary artery with subintimal entry was seen in two (7%) cases, and the rest (three cases) could not be crossed. Balloon angioplasty and stenting (n = 21) were performed with good immediate angiographic results. There were no myocardial infarctions or deaths. Fourteen of 16 patients, who had completed 6 months follow-up, were asymptomatic. Angiographic evidence of in-stent restenosis was demonstrable in one case. Successful recanalization of total coronary occlusions by using Cross-wire can be expected in 83% cases, with reasonable safety.     

Formamidinium‐Based Dion‐Jacobson Layered Hybrid Perovskites: Structural Complexity and Optoelectronic Properties

Layered hybrid perovskites have emerged as a promising alternative to stabilizing hybrid organic–inorganic perovskite materials, which are predominantly based on Ruddlesden‐Popper structures. Formamidinium (FA)‐based Dion‐Jacobson perovskite analogs are developed that feature bifunctional organic spacers separating the hybrid perovskite slabs by introducing 1,4‐phenylenedimethanammonium (PDMA) organic moieties. While these materials demonstrate competitive performances as compared to other FA‐based low‐dimensional perovskite solar cells, the underlying mechanisms for this behavior remain elusive. Here, the structural complexity and optoelectronic properties of materials featuring (PDMA)FA_n–1Pb_nI_3n+1 (n = 1–3) formulations are unraveled using a combination of techniques, including X‐ray scattering measurements in conjunction with molecular dynamics simulations and density functional theory calculations. While theoretical calculations suggest that layered Dion‐Jacobson perovskite structures are more prominent with the increasing number of inorganic layers (n), this is accompanied with an increase in formation energies that render n > 2 compositions difficult to obtain, in accordance with the experimental evidence. Moreover, the underlying intermolecular interactions and their templating effects on the Dion‐Jacobson structure are elucidated, defining the optoelectronic properties. Consequently, despite the challenge to obtain phase‐pure n > 1 compositions, time‐resolved microwave conductivity measurements reveal high photoconductivities and long charge carrier lifetimes. This comprehensive analysis thereby reveals critical features for advancing layered hybrid perovskite optoelectronics.     

Low loss matching (LLM) design technique for power amplifiers

This paper describes a design methodology used for the development of multistage broadband power amplifiers. The method uses the measured small-signal S-parameters and loadpull data in association with low loss matching (LLM) design technique. The Q-point of the amplifier was selected for class-AB operation of the device in order to obtain the maximum power-added efficiency (PAE) and bandwidth. In the design optimization using loadline techniques, four sets of S-parameter data, corresponding to device low gain, high gain, low current, and high current, were used. These data files represent the possible fabrication changes and allow realization of a design more tolerant to process variations.     

Surface topography and mechanical properties of carbon fibres

Surface topography of polyacrylonitrile based carbon fibres preoxidized under a variety of conditions has been studied in detail. Only those carbon fibres processed under optimum conditions are found to possess defect free surface topography. Changes in surface topography and the tensile strength of carbon fibres with processing conditions have been discussed.     

2–8 GHz 8-W Power Amplifier MMIC Developed Using MSAG MESFET Technology

Design approach and test data for a two-octave bandwidth HPA developed using GaAs based multifunction self aligned gate metal semiconductor field effect transistor with multilevel plating monolithic microwave integrated circuit (MMIC) technology are presented. A low loss matching design technique was used in the development of a two-stage power amplifier. The broadband amplifier has exhibited 8 W power output and better than 16% PAE over the 2.0-8.0 GHz frequency range. To our knowledge, these results represent the state-of-the-art in output power for multi-octave S/C-band power MMIC amplifiers.     

Air Gap Effects in LX‐17

Three experiments done over twenty years on gaps in LX‐17 are described. For the detonation front moving parallel to the gaps, jets of gas products were seen coming from the gaps at velocities 2 to 3 times greater than the detonation velocity. A case can be made that the jet velocity increased with gap thickness but the data are scattered. For the detonation front moving transverse to the gap, time delays were seen. The delays roughly increase with gap width, going from 0–70 ns at “zero gap” to around 300 ns at 0.5–1 mm gap. Larger gaps of up to 6 mm width almost certainly stopped the detonation, but this was not proved. Real‐time resolution of the parallel jets and determination of the actual re‐detonation or failure in the transverse case needs to be achieved in future experiments.